利用煤矸石制备泡沫陶瓷的研究

以煤矸石为研究对象,利用XRD和XRF技术,研究了煤矸石的矿物组成和化学成分.以煤矸石和低品位铝矾土为主要原料,长石作为助熔剂,振实成型后在1 200℃下焙烧成泡沫陶瓷.结果 表明,当原料中煤矸石的含量为61wt％时,所制备泡沫陶瓷的基本性能为:导热系数0.059 W/(m·K)、体积密度118.6 kg/m3、体积吸水率1.3％、抗压强度1.3 MPa、抗折强度1.4 MPa.利用煤矸石制备泡沫陶瓷,为煤矸石综合利用提供了一条可行的途径.     

Precipitating spinel into precursor glass and its assistance in crystallization

The crystallization phenomena of spinel in CaO-MgO-Al₂O₃-SiO₂-Fe₂O₃ glass have received much attention due to the particular role in preparation of glass-ceramic materials, which represent an effective option to manage hazardous waste. In this study, both preliminary spinel and secondary spinel were precipitated in the precursor glass. The formation of these spinel was meticulously assessed by a combination of X-ray diffractometry and scanning electron microscopy. The structure of the microenvironment in the precursor glass was characterized by Raman spectrums. These advanced techniques highlight the potential for one-step crystallization of the glass. The investigation, which focused on one-step crystallization, demonstrated the growth of pyroxene on spinel accompanying a migration of chromium. The results also show the microstructure of the obtained glass-ceramic was very dependent on the heat-treat temperature. This study not only unambiguously reveals the precipitation mechanisms of spinel but also provides more documentation for one-step crystallization in the glass-ceramics field.     

基于个体协同触发强化学习的多机器人行为决策方法* .txt

摘要：为了提高多机器人行为最优决策控制中强化学习的效率和收敛速度，研究了多机器人的分布式马尔科夫建模与控制策略。根据机器人有限感知能力设计了个体 协同感知触发函数，机器人个体从环境观测结果计算个体 协同触发响应概率，定义一次触发过程后开始计算联合策略，减少机器人间通讯量和计算资源。引入双学习率改进Q学习算法，并将该算法应用于机器人行为决策。仿真实验结果表明，当机器人群组数量在20左右时，本文算法的协同效率较高，单位时步比为1085 0。同时距离调节参数η对机器人协同搜索效率有影响，当η=0008时，所需的移动时步比和平均移动距离都能达到最小值。通过双学习率的引入，该算法较基于环境模型的强化学习算法具有更高的学习效率和适用性，平均性能提升35%，对于提高多机器人自主协同能力具有较高的理论意义及应用价值。 .txt     

A facile method for preparation of PGS@ZB‐N and gas‐sol alternating synergistic effect for fire resistance of EVA

Through the simple precipitation of palygorskite (PGS) by zinc borate (ZB) (to make PGS@ZB) and the decoration of PGS@ZB by dodecylamine (N), a novel organic‐inorganic@inorganic hybrid flame retardant of PGS@ZB‐N was prepared and was incorporated with ethylene vinyl acetate copolymer (EVA) to improve its flame retardance. The structure and morphology of PGS@ZB‐N were characterized by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), and scanning electron microscopy (SEM), and it was confirmed that the PGS@ZB‐N hybrid had been successfully prepared. The flame retardancy and burning behavior of EVA/PGS@ZB‐N/EG (EG = expandable graphite) composite were studied through thermogravimetric analysis (TGA), limiting oxygen index (LOI), UL‐94 (by the vertical burning test), and cone calorimeter test (CCT) characterizations. The prepared EVA/PGS@ZB‐N/EG composite obtained an LOI value of 41.2% with the addition of 30 wt% PGS@ZB‐N/EG. It was found that EVA/PGS@ZB‐N/EG was protected through a gas phase and condensed phase alternating synergistic effect mechanism.     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

内嵌纳凝胶阴离子交换聚甲基丙烯酸羟乙酯复合晶胶分离苯乳酸研究

采用超声乳化聚合法制备了聚甲基丙烯酸丁酯纳凝胶，然后经结晶致孔法制备了内嵌纳凝胶的甲基丙烯酸羟乙酯纳晶胶，对其接枝功能单体N，N，N-三甲基乙烯基苯甲氯化铵，得到内嵌纳凝胶阴离子交换纳晶胶，用于从发酵液中分离苯乳酸。结果表明：所得纳晶胶具有良好的渗透性能和轴向分散性能，在流速为1 cm·min^-1时，不同配比纳晶胶对牛血清白蛋白的吸附容量为3.9~5.4 mg·ml^-1；将质量比为 8∶2（HEMA∶pBMA）的纳晶胶用于从转化液中分离苯乳酸，所得苯乳酸的纯度达89.24%，回收率93.74%，分离效果好，表明其在生物分离方面有良好的应用前景。     

In-situ crystal growth and photoluminescence properties of YBO3: Tb3+ microstructures

Three-dimensional (3D) YBO₃:Tb³⁺ flower-like and dense flower-like hierarchitecture constituted of nanoflakes are solvothermally synthesized in the presence of polyborate precursors in the mixture of ethanol and water. The growth process of the YBO₃:Tb³⁺ flowers and dense flowers was explored based on the time-dependent experiment and the results showed that the growth mechanism follows an in situ growth rather than self-assembly process as reported previously. YBO₃:Tb³⁺ morphologies composed of nanoflakes are achieved by controlling the concentration of ethanol and dependence of photoluminescence on morphology was studied. Remarkable photoluminescence enhancement was observed for YBO₃:Tb³⁺ with flower-like morphology demonstrating the potential of the microstructure in future applications as a green phosphor. Such a synthetic method and growth mechanism may be applied to fabricate complex 3D architectures of other materials.     

7050铝合金单峰时效热处理工艺及性能研究

利用材料相图及性能模拟软件JMatPro对7050铝合金进行模拟计算，得到7050铝合金的TTT和CCT曲线。合金的TTT曲线整体呈“C”形，GP区、亚稳相和稳定相鼻尖温度分别为140、330、380 ℃，对应的孕育时间为0.002、0.007、0.200 h，η′相无析出的临界冷却速率为2 ℃/s。采用力学性能和电镜组织观察的方法，研究7050铝合金单峰时效热处理工艺。结果表明:当温度达到485 ℃时，在DSC曲线上出现吸热峰；在120 ℃下进行时效处理，随着时效时间的延长，合金的强度硬度持续增加，合金断后伸长率先增加后减小，时效70 h未见过时效特征，当时效8 h时，合金强度和韧性有较好配合，抗拉强度为593 MPa，屈服强度为516 MPa，断后伸长率为12.6%，试样拉伸断口均呈现穿晶韧窝型断裂与沿晶断裂的混合式断口形貌。